Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
Right here in the next paragraph you can discover additional worthwhile additional info when it comes to How to Install a Bathtub Yourself.
Installing a bathtub isn't specifically brain surgery, however it does need strong plumbing, carpentry, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a reasonably tough job. If the old tub is easily accessible, the job can relocate immediately; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require an assistant to leave the old bathtub and also embeded in the new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. As opposed to working with a specialist to take over a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly aid you set up a brand-new bath tub in your washroom if you have actually already gotten a new tub and don't need to alter the plan of your previous water pipelines.
Your tools and also material checklist need to make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the limited access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Before carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap as well as the sink. Safeguard the faucet in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the bath tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply and inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of a minimum of once as this will settle it into its final setting.
Planning for the Installment
First of all, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a stiff seal, triggering the water to penetrate the wall surface between the bath and the tiling, leading to problems with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water before securing, to enable the motion experienced when the tub is in use. The sealant can break relatively early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles utilizing waterproof or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that article on Tools You Need to Install a New Bathtub from an acquaintance on our other web page. Do you know about another person who is excited about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Do not hesitate to share it. Thank you so much for your time invested reading it.
Excellence? Just call! Report this page